Plumber's Essentials: Your Key to Bathtub Installation
Book A ServiceRight here down the page you can discover some excellent tips in regards to How to Install a Bathtub.
Installing a bath tub isn't precisely brain surgery, but it does need solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is additionally a moderately difficult task. If the old bathtub is conveniently available, the task can relocate immediately; if you need to open up a wall surface to remove the old bathtub and place the new tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will certainly require a helper to vacate the old tub as well as embeded in the brand-new one. Ensure you have qualified on your own for the task as well as fit attempting it. As opposed to working with a professional to take control of a halfway-completed job, it is better to consider employing one before you start. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly assist you install a brand-new bathtub in your bathroom if you have actually already acquired a new bathtub as well as do not need to change the plan of your previous supply of water pipelines.
Your tools as well as product checklist ought to consist of the following:
Preparing for the Installment
Firstly, the supporting frame supplied with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to see to it that if the tap features a plastic washer, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to avoid pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is separate the water. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be fairly problematic because of the restricted gain access to that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning during this process. As soon as the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Tub
Utilizing the two wood boards under its feet, put the bathtub in the required placement. The wooden boards are useful in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Turn on the water as well as inspect all joints and brand-new pipework for leaks and tighten them if needed. Fill up the tub as well as likewise inspect the overflow outlet and the normal outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bathtub needs to wait up until the bathtub has actually been utilized at least when as this will resolve it into its last setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making certain that the washers are in location in between the tap and also the sink. Secure the tap in position with the manufacturer given backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be linked to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall in between the bathroom as well as the tiling, leading to complications with moisture and also possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes as well as cartridges, as well as can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the market. It is suggested to fit the ceramic tiles using waterproof or water-proof sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm certainly very inquisitive about Installing A Bathtub and I am hoping you enjoyed the blog entry. Sharing is nice. You won't know, you may just be helping someone out. We take joy in reading our article about A Step-by-Step Guide to Installing a Bathtub.
Schedule A Service